rudeboy.htm Thinking Like a Cracker

	Thinking Like a Cracker A Lesson For Beginners	Not Assigned
15 March 1998	by The _RudeBoy_ [PC]
	Courtesy of Fravia's page of reverse engineering	slightly edited by fravia+
fra_00F5 980314 tudeboy 1000 NA xx	An important essay: RudeBoy underlines a VERY IMPORTANT truth: targets are made by programmers (of course) and programmers use a STANDARD approach. Cracking and reversing should always TAKE ACCOUNT of this. A simple truth that you better learn, understand and use.
	There is a crack, a crack in everything That's how the light gets in
Rating	(x)Beginner ( )Intermediate ( )Advanced ( )Expert

Thinking Like a Cracker
A lesson for beginners
Written by The _RudeBoy_ [PC]

Introduction


	This essay is aimed towards beginning crackers, and helping them to think like a
cracker.  I can't count how many times I have been asked by a beginning cracker about why
they can patch a program so that it says that it's been registered, but then when they 
restart the application it no longer says that it's registered.  The solution is usually
quite simple, but requires you to "think like a cracker".

Tools required

W32Dasm 8.9 (or whatever version you prefer)
Hex Workshop (or your favorite hex editor)
PolyView 3.00 beta 9

Target's URL/FTP

http://www.polybytes.com/betafiles/pvbeta.exe

Program History

Essay

Before we get started with cracking our target, PolyView 3.00 beta 9, we need
a lesson in thinking like a cracker/programmer.  Programmers are taught that 
whenever you have a task that is going to be done more that once, you should
create a function to do that task, and just call the function when you need to 
perform the task.  Now, most programs that use a name/serial # combination 
check the code at least twice, once when you enter the code, and once when the
program starts up.  Because of this the programmer will usually call a function
to test your reg code.  And usually, this function will be called every time the
code is checked.  At this point you should probably see where I am going with
this.  If you patch the function that is called to test the reg code, it will 
show up as valid whenever the program does it's check.

Now, for an example of this technique, on to PolyView 3.00 beta 9.

When you run the program you should notice on the menubar the "Registration" section,
and under that, "License Information".  It has a place to enter a name and a license
code.  Enter whatever you like for these values and press "OK".  If you have not
entered an integer into the license code box, you will receive an error saying "Please
enter a positive integer", otherwise you will receive the error "Registration Unsuccessful".

Fire up W32Dasm, and load PolyView.exe.  When this is done go to the string references
and look for "Registration Unsuccessful".  When you find it in the list, notice that
just above it is the string "Registration successful", and then double click on 
"Registration Unsuccessful".  You should see this section of code:

* Referenced by a  Jump at Address:004400C9(C)
|
* Possible Reference to String Resource ID=00141: "Unregistered"
                                  |
:0044016C 688D000000              push 0000008D
:00440171 8BCF                    mov ecx, edi
:00440173 E8D9070600              call 004A0951
:00440178 53                      push ebx
:00440179 53                      push ebx

* Possible StringData Ref from Data Obj ->"Registration unsuccessful. please "
                                        ->"verify that you have entered the "
                                        ->"information exactly as shown on "
                                        ->"your registration letter."
                                  |
:0044017A 684C364F00              push 004F364C
:0044017F 899E70010000            mov dword ptr [esi+00000170], ebx
:00440185 E8D88A0600              call 004A8C62

You should notice first that this section of code was referenced by a
conditional jump at 004400C9. Scroll up in w32dasm until you get 
to that location, you should see this code:

:004400B7 50                      push eax
:004400B8 51                      push ecx
:004400B9 898670010000            mov dword ptr [esi+00000170], eax
:004400BF E8DCF0FEFF              call 0042F1A0    ;IsValidCode()
:004400C4 83C408                  add esp, 00000008
:004400C7 85C0                    test eax, eax    ;The infamous test
:004400C9 0F849D000000            je 0044016C      ;je Bad_Guy

Here is where we apply what we learned earlier.  If you were to simply
NOP out the je 044016C the program would say that it is registered when
you enter in your code.  However, When you restart the program, it would
still say "Unregistered".  Remember what I said about programmers writing
one function, and calling it many times to see if the code is valid?  That
is what this author has done, the call to 0042F1A0 is the program calling
that function.  In w32dasm, goto code location 0042F1A0, and you will see
this:

* Referenced by a CALL at Addresses:
|:0040423B   , :004046B8   , :004055FA   , :0042DDBE   , :0042DE36   
|:004395C4   , :0043CE1A   , :0043D6B0   , :0043E35A   , :00440025   
|:004400BF   , :004419BC   , :0044234D   , :00452FF9   , :004531CB   
|:004B9033   
|
:0042F1A0 64A100000000            mov eax, dword ptr fs:[00000000]

Every one of those addresses is a place where this program calls the 
IsValidCode() routine to see if the program is registered.  Now, the 
question remains.how do you patch this program so that it is 
registered.  Look again to the section of code that calls the 
IsValidCode() routine, specifically at the jump to Bad_Guy.  It will 
jump if eax = 0.  So, the easiest way to patch this program is to write 
over the mov eax, dword ptr fs:[00000000] in the called function with:

push   00000001
pop    eax
ret

(In hex that would be 6A0158C3)

The function now always returns 1 in eax, and the program thinks that 
it has been registered.

Final Notes

The techniques employed here do not only apply to cracking programs with
name/reg code routines.  Do not limit yourself by thinking "Inside the Box",
these techniques can be used with many other types of protections as well.
(for example, many times a date check and a nag screen are done by
one function)

Ob Duh

I wont even bother explaining you that you should BUY this target program if you intend to use it for a longer period than the allowed one. Should you want to STEAL this software instead, you don't need to crack its protection scheme at all: you'll find it on most Warez sites, complete and already regged, farewell.

You are deep inside fravia's page of reverse engineering, choose your way out:

Back to the student essays

links

Is reverse engineering legal?